Journal of
Engineering and Technology Research

  • Abbreviation: J. Eng. Technol. Res.
  • Language: English
  • ISSN: 2006-9790
  • DOI: 10.5897/JETR
  • Start Year: 2009
  • Published Articles: 200

Full Length Research Paper

Graded PA6/PA12 blends prepared by selective laser sintering

Gean Vitor Salmoria
  • Gean Vitor Salmoria
  • CIMJECT Laboratory, Department of Mechanical Engineering, Federal University of Santa Catarina, 88040-900, Florianópolis, Santa Catarina, Brazil.
  • Search for this author on:
  • Google Scholar
Janaina Lise Leite
  • Janaina Lise Leite
  • CIMJECT Laboratory, Department of Mechanical Engineering, Federal University of Santa Catarina, 88040-900, Florianópolis, Santa Catarina, Brazil.
  • Search for this author on:
  • Google Scholar
Rodrigo Acacio Paggi
  • Rodrigo Acacio Paggi
  • CIMJECT Laboratory, Department of Mechanical Engineering, Federal University of Santa Catarina, 88040-900, Florianópolis, Santa Catarina, Brazil.
  • Search for this author on:
  • Google Scholar


  •  Received: 23 March 2017
  •  Accepted: 23 July 2017
  •  Published: 30 September 2017

References

Calder N (2001). Rapid manufacturing of functional materials. Proc. Time-Compression Technologies Conference Proceeds. Manchester, United Kingdom pp. 20-25.
 

Haseung C, Suman D (2006). Processing and properties of glass bead particulate-filled functionally graded Nylon-11 composites produced by selective laser sintering. Mater. Sci. Eng. A. 437(2):226-234.
Crossref
 

Haseung C, Suman D (2008). Functionally graded Nylon-11/silica nanocomposites produced by selective laser sintering. Mater. Sci. Eng. A. 487(1-2):251-257.
Crossref
 

Jiang W, Nair R, Molian P (2004). Functionally graded mold inserts by laser-based flexible fabrication: processing modeling, structural analysis and performance evaluation. J. Mat. Proc. Technol. 166:286-293.
Crossref
 

Joshi A, Patnaik A, Gangil B, Kumar S (2012). Laser assisted rapid manufacturing technique for the manufacturing of functionally graded materials. Conference on Engineering and Systems, SCES 2012, art. no. 6199074.
Crossref
 

Kieback B, Neubrand A, Riedel H (2003). Processing techniques for functionally graded materials. Mater. Sci. Eng. A. 362:81-105.
Crossref
 

Kim SS, Shin MW, Jang H (2012). Tribological properties of short glass fiber reinforced polyamide 12 sliding on medium carbon steel. Wear 274:34-42.
Crossref
 

Leite JL, Salmoria GV, Paggi RA, Ahrens CH, Pouzada AS (2010). A study on morphological properties of laser sintered functionally graded blends of amorphous thermoplastics. Int. J. Mater. Prod. Technol. 39:205-221.
Crossref
 

Leite JL, Salmoria GV, Paggi RA, Ahrens CH, Pouzada AS (2012). Morphology and mechanical properties of functionally graded PA12/HDPE parts by selective laser sintering. Int. J. Adv. Manuf. Technol. 59:583-591.
Crossref
 

Mahamood RM, Akinlabi ET (2017). Additive Manufacturing of Funtionally Graded Materials. In: Functionally Graded Materials. Topics in Mining, Metallurgy and Materials. Engineering. Springer, Cham. DOI 10.1007/978-3-319-53756-6_2.
Crossref
 

Palabiyik M, Bahadur S (2000). Mechanical and tribological properties of polyamide 6 and high density polyethylene polyblends with and without compatibilizer. Wear 246(1):149-158.
Crossref
 

Shishkovsky I (2001). Synthesis of functional gradient parts via RP methods. Rapid Prototyp. J. 7(4):207-211.
Crossref
 

Yusufu ACJ, Merve E, Serkan D (2014). Production of graded porous polyamide structures and polyamide-epoxy composites via selective laser sintering. J. Reinf. Plastics Compos. 33(11):1017-1036.
Crossref

 

Copyright © 2025 Author(s) retain the copyright of this article.

This article is published under the terms of the Creative Commons Attribution License 4.0

Back to Vol. 9 No. 3
Back to articles
SUBSCRIBE TO RSS
SUBMIT MANUSCRIPT
CONFERENCES