Journal of
Geology and Mining Research

  • Abbreviation: J. Geol. Min. Res.
  • Language: English
  • ISSN: 2006-9766
  • DOI: 10.5897/JGMR
  • Start Year: 2009
  • Published Articles: 172

Full Length Research Paper

Numerical and experimental studies on the effect of loading angle on the validity of flattened Brazilian disc test

Pourya Khavari*
  • Pourya Khavari*
  • Mining Exploitation Engineering, School of Mining Engineering, Faculty of Engineering, University of Tehran, Tehran, Iran.
  • Google Scholar
Mehrnoosh Heidari
  • Mehrnoosh Heidari
  • Rock Mechanics Engineering, School of Mining Engineering, Faculty of Engineering, University of Tehran, Tehran, Iran.
  • Google Scholar


  •  Received: 26 December 2015
  •  Accepted: 24 May 2016
  •  Published: 31 May 2016

References

Aliha MRM, Hosseinpour GR, Ayatollahi MR (2013). Application of cracked triangular specimen subjected to three-point bending for investigating fracture behavior of rock materials. Rock Mech. Rock Eng. 46(5):1023-1034.
Crossref

 

Alkilicgil C (2010). Development of specimen geometries for mode I fracture toughness testing with disc type rock specimens, Doctoral dissertation, PhD thesis, Middle East Technical University, Ankara.

 

Awaji H, Sato S (1978). Combined mode fracture toughness measurement by the disk test. J. Eng. Mater. Technol. 100(2):175-182.
Crossref

 

Ayatollahi MR, Aliha MRM (2008). On the use of Brazilian disc specimen for calculating mixed mode I–II fracture toughness of rock materials. Eng. Fract. Mech. 75(16):4631-4641.
Crossref

 

Barker LM (1978). Short rod KIc measurements of Al2O3. In Flaws and Testing, Springer US pp. 483-494.
Crossref

 

Chen CH, Chen CS, Wu JH (2008). Fracture toughness analysis on cracked ring disks of anisotropic rock. J. Rock Mech. Rock Eng. 41(4):539-562.
Crossref

 

Chong K, Kuruppu MD (1984). New specimen for fracture toughness determination for rock and other materials. Int. J. Fract. 26(2):R59-R62.
Crossref

 

Chowdhury MS, Song C, Gao W (2014). Probabilistic fracture mechanics with uncertainty in crack size and orientation using the scaled boundary finite element method. J. Comp. Struct. 137:93-103.
Crossref

 

Dai F, Wei MD, Xu NW, Ma Y, Yang DS (2014). Numerical Assessment of the Progressive Rock Fracture Mechanism of Cracked Chevron Notched Brazilian Disc Specimens. Rock Mech. Rock Eng. pp. 1-17.

 

Donovan JG, Karfakis MG (2004). Adaptation of a simple wedge test for the rapid determination of mode I fracture toughness and the assessment of relative fracture resistance. Int. J. Rock Mech. Min. Sci. 41(4):695-701.
Crossref

 

Guo H, Aziz NI, Schmidt LC (1993). Rock fracture-toughness determination by the Brazilian test. J. Eng. Geol. 33(3):177-188.
Crossref

 

Hoek E, Martin CD (2014). Fracture initiation and propagation in intact rock–A review. J. Rock Mech. Geotech. Eng. 6(4):287-300.
Crossref

 

Kaklis KN, Agioutantis Z, Sarris E, Pateli A (2005). A theoretical and numerical study of discs with flat edges under diametral compression (flat Brazilian test). In 5th GRACM Int. Congress Comput. Mech. 1:437-444.

 

Keles C, Tutluoglu L (2011). Investigation of proper specimen geometry for mode I fracture toughness testing with flattened Brazilian disc method. Int. J. Fract. 169(1):61-75.
Crossref

 

Khavari P (2015). Investigation and Comparison between Methods of Determining the crack Toughness in Rocks, Iranian National Conference on Geology and Resources Exploration (In Persian).

 

Labuz JF, Arno Z (2012). "Mohr–Coulomb failure criterion." The ISRM Suggested Methods for Rock Characterization, Testing and Monitoring: 2007-2014. Springer Int. Publishing pp. 227-231.

 

Ouchterlony F (1981). Extension of the compliance and stress intensity formulas for the single edge crack round bar in bending. ASTM STP 745:237-256.
Crossref

 

Ouchterlony F (1988). Suggested methods for determining the fracture toughness of rock. Int. J. Rock Mech. Min. Sci. 25(2):71-96.
Crossref

 

Rocco C, Guinea GV, Planas J, Elices M (1999). Size effect and boundary conditions in the Brazilian test: experimental verification. J. Mat. Struct. 32(3):210-217.
Crossref

 

Roylance D (2001). Introduction to fracture mechanics. Massachusetts Institute of Technology, Cambridge.

 

Sarris E, Agioutantis Z, Kaklis K, Kourkoulis SK (2007). Numerical Simulation of the Cracked Brazilian Disc under Diametral Compression. In Bifurcations, Instabilities, Degradation in Geomechanics, Springer Berlin Heidelberg 403-430.
Crossref

 

Sheity DK, Rosenfield AR, Duckworth WH (1985). Fracture Toughness of Ceramics Measured by a Chevron‐Notch Diametral‐Compression Test. J. Am. Ceram. Soc. 68(12):C-325.
Crossref

 

Szendi-Horvath G (1980). Fracture toughness determination of brittle materials using small to extremely small specimens. J. Eng. Fract. Mech. 13(4):955-961.
Crossref

 

Thiercelin M, Roegiers JC (1986). Fracture toughness determination with the modified ring test. In Proc. Int. symp. Eng. Complex Rock Formation, Beijing, China pp. 1-8.

 

Wang QZ, Jia XM, Kou SQ, Zhang ZX, Lindqvist PA (2004). The flattened Brazilian disc specimen used for testing elastic modulus, tensile strength and fracture toughness of brittle rocks: analytical and numerical results. Int. J. Rock Mech. Min. Sci. 41(2):245-253.
Crossref

 

Wang QZ, Wu LZ (2004). The flattened Brazilian disc specimen used for determining elastic modulus, tensile strength and fracture toughness of brittle rocks: experimental results. Int. J. Rock Mech. Mining Sci. 41:26-30.
Crossref

 

Wang QZ, Xing L (1999). Determination of fracture toughness KIc by using the flattened Brazilian disk specimen for rocks. J. Eng. Fract. Mech. 64(2):193-201.
Crossref