Journal of
Engineering and Technology Research

  • Abbreviation: J. Eng. Technol. Res.
  • Language: English
  • ISSN: 2006-9790
  • DOI: 10.5897/JETR
  • Start Year: 2009
  • Published Articles: 198

Full Length Research Paper

Theoretical modeling of strain in the single screw feeder of cassava flash dryer

Noutegomo Boris
  • Noutegomo Boris
  • Laboratory of Mechanical and Production Engineering, University of Douala, Douala, Cameroun.
  • Search for this author on:
  • Google Scholar
Djeumako Bonaventure
  • Djeumako Bonaventure
  • Department of Mechanical Engineering, ENSAI, University of Ngaoundéré, Ngaoundéré, Cameroun.
  • Search for this author on:
  • Google Scholar
Ndjouenkeu Robert
  • Ndjouenkeu Robert
  • Department of Health and Applied Nutrition, ENSAI, University of Ngaoundéré, Ngaoundéré Cameroun.
  • Search for this author on:
  • Google Scholar


  •  Received: 01 April 2016
  •  Accepted: 07 September 2016
  •  Published: 31 July 2017

References

Bortolamasi M, Fottner J (2001). Design and sizing of screw feeders. In: Proc. Partec 2001. Int. Congr. Particle Technol. 69:27-29.
 

Burkhardt GJ (1967). Effect of pitch, radial clearance, hopper exposure and head on performance of screw feeders. Trans. ASAE. 10:685-690.
Crossref

  
 

Cleary PW (2007). DEM modelling of particulate flow in a screw feeder Model description. Progr. Comput. Fluid Dyn. Int. J. 7:128–138.
Crossref

  
 

Cundall PA, Strack ODL (1979). A discrete numerical model for granular assemblies. G’eotechnique 29(1):47-65.
Crossref

  
 

Ghosh BN (1967). Conveyance of wet parchment coffee beans by an auger. J. Agric. Eng. Res. 12(4):274-280.
Crossref

  
 

McLean AG, Arnold PC (1979). A simplified approach for the evaluation of feeder loads for mass flow bins. Powder Bulk Solids Technol. 3(3):25-28.

  
 

Metcalf JR (1962). The mechanics of the screw feeder, Proc. Inst. Mech. Eng. 180(6):131-146.

  
 

Owen PJ, Cleary PW (2010). Screw conveyor performance: comparison of discrete element modelling with laboratory experiments. Progr. Comput. Fluid Dyn. Int. J. 10(5):327-333.
Crossref

  
 

Rautenbach R, Schumacher W (1987). Theoretical and experimental analysis of screw feeders. Bulk Solids Handling 7(5):675-680.

  
 

Roberts AW, Manjunath KS (1994). Volumetric and torque characteristics of screw feeders, Proc. Powder and Bulk Solids Conf., Chicago, IL, USA. pp. 189-208.

  
 

The International Commission of Agricultural Engineering (1999). (CIGR Handbook) of Agricultural Engineering Volume IV Agro-Processing Engineering Michigan State University, USA.

View

  
 

Yu Y, Arnold PC (1996). Influence of screw feeders on bin flow patterns. Pow. Technol. 88:81-87.
Crossref

  
 

Yu Y, Arnold PC (1997). Theoretical modeling of torque requirements for single screw feeders. Pow. Technol. 93:151-162.
Crossref

  

 

Copyright © 2024 Author(s) retain the copyright of this article.

This article is published under the terms of the Creative Commons Attribution License 4.0

Back to Vol. 9 No. 1
Back to articles
SUBSCRIBE TO RSS
SUBMIT MANUSCRIPT
CONFERENCES